ASME B46.1 PDF

This self-study course is designed to be taken at your convenience and on your own schedule. You have 90 days to finish the course from the time of purchase. Readed, ASME B Surface Topology – Free download as PDF File .pdf) or read online for free. Revision: Published Date: January ; Status: Superseded By: Superseded By : ASME B; Document Language: Published By: ASME International (ASME).

Author: Mukazahn Balmaran
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Automotive
Published (Last): 11 October 2005
Pages: 106
PDF File Size: 12.96 Mb
ePub File Size: 19.92 Mb
ISBN: 526-5-81931-865-2
Downloads: 92813
Price: Free* [*Free Regsitration Required]
Uploader: Meztigal

This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.

References to other useful works are included as footnotes. This statistical averaging procedure must be clearly defined in asmr surface specifications, and cannot be inferred by stated compliance with ASME B Classification of Instruments for Surface Texture Measurement When the probe is raster scanned over the surface, a profile is generated through the collection of sequential measurements.

What is Surface Texture B46.1 for Stainless

However, with in the definitions or recommendations mayhave suchanextensiverevision,inconsistencies been overlooked. The arcs and the radii must contain the stylus tip profile. The instrument nonlinearity is the deviation in measured z axis displacement as a function of the actual z axis stylus displacement. This Standard is not concerned with error of form and flaws, but discusses these two factors to distinguish them from surface texture.

The World’s First $19k 3D Profilometer:

If the process usedproduces parts that vary widely in roughness average Rover the surface, the use of a statistical average of a number of measurements may be desirable. Stewart, Micromatic Textron P.

  ICD-AX412 MANUAL PDF

The profile representing waviness and form error is then identical to the roughness mean line and is equal to the subtraction of the roughness profile from the total profile. The transmission characteristic for the mean line has the following equation: The roughness comparison specimens are intended to assist workshop personnel in evaluating and controlling the surface topography of the workpieces by comparing them with the specimen surface.

For tolerances and uncertainties, see Table A small change in any of the above factors may have a marked effect on the surface produced. As the tip size increases, the measuredroughness average R, decreases for this type of specimen. Someexamples are a Fourier filter, apolynomial fit using least squares techniques, or a directional based filter to eliminate or enhance directional surface features such as lay.

The cutoff of the filter is the nominal rating in millimeters mm of the long wavelength limit of the electrical analog or digital filter that attenuates the long wavelength waviness fluctuations of the surface profiletoyield the roughness profile. Such amap often consists of a set of parallel profiles. Nominal Values of R, and S.

What is Surface Texture B for Stainless

Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework. There will be no addenda or written interpretations of the requirements of this Standard issued to this edition.

For surfaces produced by most material removal processes, the methods divergencefor R, measurements is usually small.

The magnification ratio or aspect ratio is the ratio of the z magnification to the x magnification. The x axis profile component deviations are those deviations between the actual profileand the measured profile in the x direction. The transmission band for roughness for the Gaussian filter is the range of wavelengths of the surface profile that are transmitted by the short- and long-wavelength cutoff roughness filters.

  ENFERMEDAD DE MEIGE PDF

Profilometer and 3D Optical Profiler – Filmetrics

On prior drawings whenthecutoffisnotspecified, the 0. A common method of measuring the roughness average uses the motion of a sharppointed stylus over the surface and the conversion of the displacement normal to the surface into an output reading proportional to the roughness average.

For tolerances of certain higher R, values in this range, see Table 1 Wheeler, Tencor Instruments, Wsme. The mean peak spacing S, thus has a value of approximately 15 pm. If there are many discontinuities, interpretation becomes extremely difficult.

A schematic diagram of this classification with some examples isshownin Fig. No part of this publication may be copied or reproduced in any form, electronic retrieval system or otherwise, without the prior written permission the American National Standards of Institute, 11 West 42nd Street, New York, NYwhich holds reproduction rights in the United States.

The outer surface on each side of the groove is to be ignored for a sufficient length w 1 to avoid the influence of any rounding of the comers.